IP Rating Explained: What IP44, IP65 and IP67 Really Mean

IP rating explained: what the two digits mean, how IP compares with NEMA types and wet location listings, and eight mistakes that let water in.

IP rating is printed on almost every light fixture, outdoor box and garden gadget you buy: IP44 on a porch light, IP65 on a shower trim, IP67 on a pond pump. Most people know a higher number sounds better. Few know what the two digits actually mean, and almost nobody is told where it goes wrong after installation. This guide explains how the IP rating works, how it compares with the NEMA ratings and the damp and wet location listings you see in the US, and the mistakes that leave a “waterproof” fixture full of water.

IP rating: how the code is built

IP stands for ingress protection. The rating comes from the international standard IEC 60529 and always has the same shape: the letters IP followed by two digits.

  • The first digit tells you how well the enclosure keeps out fingers, tools, solid objects and dust.
  • The second digit tells you how well it keeps out water.
  • An X in place of a digit means that property was not tested or not declared.

So IP44 means protected against objects larger than 1 millimeter, about the thickness of a wire, and against water splashing from any direction.

The first digit: fingers, objects and dust

DigitProtected againstIn plain terms
0NothingOpen equipment
1Objects over 50 mm (about 2 in)The back of a hand
2Objects over 12.5 mm (about 1/2 in)A finger
3Objects over 2.5 mm (about 1/10 in)A tool or a thick wire
4Objects over 1 mm (about 1/25 in)A thin wire
5Dust protectedSome dust gets in, not enough to cause trouble
6Dust tightNo dust gets in
First digit of the IP rating, per IEC 60529

The second digit: water

DigitProtected against
0Nothing
1Vertically dripping water
2Dripping water with the enclosure tilted up to 15°
3Spraying water, up to 60° from vertical
4Splashing water from any direction
5Water jets
6Powerful water jets
7Temporary immersion, up to 1 meter (about 3 ft)
8Continuous immersion, under conditions set by the manufacturer
9High pressure, high temperature jets, often marked 9K
Second digit of the IP rating, per IEC 60529

Sometimes a letter follows the digits. A, B, C or D means the protection against touching live parts is better than the first digit suggests, tested with a probe of 50, 12, 2.5 or 1 mm. IP20D, for example, has no water protection at all, but even a thin wire cannot reach anything live.

IP rating vs NEMA rating

In the US you will often see a NEMA type instead of an IP rating, especially on electrical boxes, disconnects and panels. NEMA types describe the environment an enclosure is built for: Type 1 for general indoor use, Type 3R for outdoor use where rain and sleet are the concern, Type 4 for hose directed water, Type 4X for the same plus corrosion, and Type 6P for prolonged submersion.

Conversion tables circulate online, and they usually line up roughly like this: Type 3R near IP24, Type 4 and 4X near IP66, Type 6P near IP68. Treat those as rough guides only. A NEMA type also covers things IP does not test, such as corrosion, ice and oil, so a NEMA rating can be read as meeting a given IP rating, but an IP rating cannot be read as meeting a NEMA type.

What the NEC asks for: damp and wet locations

Here is the part most guides skip. The National Electrical Code does not ask for an IP number. It sorts locations into dry, damp and wet, and it asks for equipment that is listed for that location. A covered porch is typically a damp location. An uncovered deck, the inside of a shower or anything exposed to rain is a wet location. What your electrical inspector looks for is the listing on the product, “suitable for damp locations” or “suitable for wet locations”, from a recognized testing lab such as UL or ETL.

An IP rating on the box is useful information, but it does not replace that listing. A cheap import marked IP65 without a recognized listing mark is exactly the kind of product an inspector can reject, because the code requires listed equipment to be installed according to its listing. The bathroom is where this matters most, and our guide to bathroom electrical safety explains how the US protects that room.

IP rating in practice: what goes wrong

In fifteen years of inspecting electrical installations, I saw the same mistakes come back with water and enclosures. None of them show up on the packaging.

1. An X is not a zero

IPX4 does not mean the product has no protection against solid objects. It means that property was not declared. And IP4X says nothing at all about water. If you need splash protection, read the second digit.

2. Higher is not always better

Up to 6, a higher water digit includes the lower ones. At 7 and 8 that stops. A product rated for immersion is not automatically tested against water jets. If it needs both, it carries a double marking such as IPX5/IPX7.

3. The rating only holds if the installation is right

The IP rating on the box applies to the product as the manufacturer intended it. A cable that enters without the right gland or fitting, a gasket that is pinched or missing, a cover that does not seat, or a fixture mounted upside down with its weep holes on top: in every one of those cases the real protection is far below the number on the box.

4. An outdoor outlet is only protected with the cover closed

A flat flip cover keeps rain out only while nothing is plugged in. That is why the NEC asks for an in use cover, the bubble cover, on 15 and 20 amp receptacles in wet locations: it stays weatherproof with a cord plugged in. Outdoor receptacles also need GFCI protection, as our guide to GFCI requirements explains.

5. Recessed lights are often rated from the front only

Many recessed lights and shower trims carry a high rating on the room side and a much lower one on the ceiling side. That is fine in a dry attic, and a problem where moisture can reach the back of the fixture. Read the full specification, not just the headline number.

6. The weakest part sets the rating

An IP65 light fed from an indoor junction box is not an IP65 installation. Every box, fitting and splice in the wet area needs to match the location. The same goes for a feeder to an outbuilding, where the boxes and conduit outside are part of the job. See our guide to a subpanel in a detached garage.

7. No marking, no protection

If a product shows no IP rating and no damp or wet location listing, do not assume it can take water. For any location where water can reach it, choose equipment that states its rating and listing clearly.

8. Water and power together need more than an enclosure

An enclosure keeps water out of the equipment. It does not protect the person standing in the water. That job belongs to GFCI protection and bonding, which is why a hot tub needs much more than a weatherproof box. Our guide to hot tub wiring walks through it.

Many of these turn up again in home inspections. Our list of the 22 findings in every electrical inspection report shows where.

Water protection is not shock protection

One more source of confusion: the IP rating says nothing about shock protection when something fails inside the product. That is the job of the protection class, grounded or double insulated. Our guide to double insulated tools and appliances explains the difference.

IP rating: the short version

The IP rating has two digits: the first for objects and dust, the second for water. An X means not declared, and above 6 a higher number does not include the lower ones. In the US, what counts for the inspector is the damp or wet location listing and, for enclosures, the NEMA type. And whatever the number, it only holds if the product is installed exactly as the manufacturer intended, with the right fittings, gaskets and covers.

This article is general information about residential electrical systems, not a code ruling for your home. Code adoption varies by state and city, and your local electrical inspector has the final word. Have any work done by a licensed electrician.

Rahmouni, author of FIXMIRO

Who writes this

FIXMIRO is written by Rahmouni, an industrial engineer who spent fifteen years inspecting electrical installations and seven inspecting gas. What you read here is what he used to explain to homeowners while standing at their panel, written out properly.

Use the free calculators

Or browse all the guides.