Available Fault Current: Can Your Breaker Actually Stop a Short Circuit?

Available fault current decides whether your breaker can stop a short circuit. What the number on your breaker means, and when 10,000 amps is not enough.

Available fault current is the current that rushes through your wiring the instant a hot conductor touches the neutral or a grounded part directly. No appliance in between, nothing to slow it down, only the wires and the utility transformer behind them. In a fraction of a second it can climb past ten thousand amps.

Your breaker has to stop that current. Not just notice it, but actually open the circuit without destroying itself in the process. The number that tells you whether it can is printed right on the breaker, and almost nobody knows what it means.

Available fault current: what happens in that one instant

Under normal load, the appliance decides how much current flows. A 1,500 watt kettle on a 120 volt circuit draws about 12.5 amps, and neither the wire nor the breaker has any trouble with that.

In a short circuit the appliance drops out of the picture. The only thing still limiting the current is the impedance of everything between you and the utility transformer: the transformer itself, the service drop or underground lateral, the service entrance conductors and the wiring inside your house. The lower that impedance, the higher the fault current.

In those few milliseconds an enormous amount of energy is released. When the breaker opens, an arc forms inside it, and the breaker has to extinguish that arc. If it cannot, the breaker can rupture, its contacts can weld shut, or the panel can catch fire.

Where available fault current comes from

Two things decide almost all of the fault current at your panel.

The utility transformer. In most neighborhoods that is a pole mounted or pad mounted transformer shared by a handful of houses. A larger transformer with a lower impedance can push more current into a fault. Both numbers are on its nameplate: the size in kVA and the impedance as a percentage.

Here is a rough example for a 50 kVA transformer at 120/240 volts with an impedance of 2 percent, at the transformer terminals and before any wire is added:

Full load current: 50,000 VA / 240 V = about 208 amps
Fault current: 208 A / 0.02 = about 10,400 amps

That is already above what most standard residential breakers are rated for, and it is not an unusual transformer.

The distance. Every foot of conductor between the transformer and your panel adds impedance and brings the fault current down. A house right next to a pad mounted transformer with a short lateral sees close to the full value. A house at the end of a long rural drop sees a lot less.

Put your own transformer size, impedance and service conductors into the available fault current calculator and see roughly what your panel is exposed to.

The NEC sets no fixed limit for a house

You might expect the code to say that a home never sees more than a certain number of amps, so every breaker can simply be chosen to match. It does not. The National Electrical Code works the other way around.

NEC 110.9 requires equipment that interrupts current at fault levels to have an interrupting rating sufficient for the current available at its line terminals. NEC 110.10 adds that the overcurrent devices, the impedance of the circuit and the short circuit current ratings of the equipment have to be selected so the fault is cleared without extensive damage. In plain words: the breaker has to be rated for the fault current at the place where it is installed, whatever that current turns out to be.

There is a catch for homeowners. NEC 110.24 requires the available fault current to be marked in the field at service equipment, but only at buildings other than dwelling units. At your house, nobody is required to write that number on the panel. So you will almost never see it, even though every breaker in the box depends on it.

What is printed on your breaker

Pull the panel door open, leave the dead front cover on, and look at the breakers. Most of what matters is printed on the side, the front or the handle.

The ampere rating. The big number on the handle, such as 15, 20 or 30. This is the current the breaker protects the wire against in normal service. It has nothing to do with a short circuit.

The voltage rating. Usually 120/240 V on a residential breaker.

The interrupting rating. This is the one this article is about. It is the largest fault current the breaker can safely open, marked as something like 10,000 A, 10kA or 22kA. Most standard residential breakers are rated at 10,000 amps. Higher rated versions exist, usually at a higher price.

The listing mark. A UL or other recognized testing laboratory mark, showing the breaker was tested to the standard for circuit breakers.

HACR. Found on many breakers, it means the breaker is suitable for heating, air conditioning and refrigeration equipment.

The terminal ratings. Which conductor material the terminal accepts, such as CU or CU/AL, and at what temperature, such as 60/75°C. That temperature matters for wire sizing, which is why the table value for a wire is not always the value you can use, as explained in wire derating.

GFCI breakers, AFCI breakers and dual function breakers carry the same kind of marking. They are full circuit breakers with an added protective function, so they also have to be able to interrupt the fault current at their location.

People often mix up the two numbers, so to be clear. The available fault current is a property of your service: how much current can flow into a fault. The interrupting rating is a property of the breaker: how much current it can safely stop. The second number has to be equal to or higher than the first. Never lower.

The label inside the panel door

The panel has its own label, usually on the inside of the door. It tells you two things worth knowing.

First, which breaker types are allowed in that panel. Under NEC 110.3(B), equipment has to be installed according to its listing and labeling, so a breaker that merely fits the bus is not automatically allowed on it.

Second, the short circuit rating of the panel and any series rated combinations. NEC 240.86 allows a branch breaker with a lower interrupting rating to be used behind a main breaker that has a higher one, but only in a combination that was tested together and is marked on the equipment. That is how a panel with 10,000 amp branch breakers can carry a higher overall rating. Change one of those breakers for a different type, and the series rating no longer applies.

Where it goes wrong in practice

The breaker that happened to be in the truck. One breaker gets replaced with whatever was at hand, from a different brand, without anyone reading the panel label. It fits, it works, and it may not be listed for that panel or part of its series rating. That one breaker becomes the weak link in an otherwise good panel.

A house close to a big transformer. A short lateral from a large pad mounted transformer can deliver more than 10,000 amps at the panel. Then standard breakers are not enough, and the panel needs higher rated breakers or a listed series combination that covers the actual fault current.

A utility upgrade nobody told you about. When the utility replaces a transformer with a larger one, the fault current at every house on it can go up. Your panel was fine the day it was installed. It is still the same panel, facing a bigger number.

Old panels. A panel from the sixties or seventies was selected for the service of its day. On some brands the question is not even the interrupting rating but whether the breaker opens at all, as explained in why Federal Pacific breakers fail. If you are deciding what to do with an older installation, old house wiring: do you really need to rewire? covers the panel question as well.

Calculating available fault current at your panel

The fault current at your panel depends on the transformer size and impedance, and on the length, size and material of the conductors between the transformer and your panel. With those numbers you can make a solid estimate yourself.

If you do not know the transformer data, ask your utility. Many utilities will provide the available fault current at your service on request, and an electrician planning a new service or a panel upgrade should be asking for it anyway.

Run the numbers with the available fault current calculator, then compare the result with the interrupting rating printed on your breakers.

And at the end of a long circuit?

This is where the story turns around. At the panel, the fault current is at its highest. The further you follow a circuit, the more wire is in the way and the lower the fault current becomes.

At the far end of a long run, for example out to a shed or a detached garage, the fault current can drop so low that the breaker no longer trips instantly. It still trips eventually, on its slow thermal element, but in the meantime the metal parts of the faulted equipment can stay energized. Now the problem is not too much current, but too little.

That is why NEC 250.4(A)(5) requires an effective ground fault current path with low impedance, so the breaker actually operates. It is also why NEC 250.122(B) requires the equipment grounding conductor to be increased in size when the circuit conductors are upsized for voltage drop. We worked a long run through from start to finish in wire size for a 300 foot run, and you can check your own run with the voltage drop calculator.

So a breaker has two jobs. It has to interrupt the highest fault current at the panel, and it still has to react quickly to the lowest fault current at the end of the circuit.

What gets checked

When a new service or a replacement panel is permitted, the electrical inspector can check that the interrupting ratings cover the available fault current, that the breakers are the types listed on the panel label, and that each breaker matches the wire it protects.

A home inspector at a sale will not calculate fault current, but will write up the visible symptoms: mixed breaker brands, a breaker too large for its wire, two wires under one terminal. Those show up in almost every report, and we listed them in the 22 findings in every electrical inspection report.

In fifteen years of inspecting electrical installations, the interrupting rating was the marking I saw people read least. Everyone looks at the number on the handle. Hardly anyone looks at the small print beside it.

The short version

Available fault current is the current that flows when a hot conductor faults directly, and it is highest at your panel. The NEC sets no fixed maximum for a house. Instead, every breaker has to be rated to interrupt the fault current at the place where it is installed.

So open your panel door and look. Does every breaker show an interrupting rating, and is it a type listed on the panel label? If you live close to a large transformer, if your service was recently upgraded, or if one breaker looks different from the rest, ask a licensed electrician to check the available fault current against what is installed.

This article is general information about residential electrical systems, not a code ruling for your home. Code adoption varies by state and city, and your local electrical inspector has the final word. Have any work done by a licensed electrician.

Rahmouni, author of FIXMIRO

Who writes this

FIXMIRO is written by Rahmouni, an industrial engineer who spent fifteen years inspecting electrical installations and seven inspecting gas. What you read here is what he used to explain to homeowners while standing at their panel, written out properly.

Use the free calculators

Or browse all the guides.